TSC-CМ-3 / TSC-CМ-6
Triac controller with MODBUS-RTU control
This electronic fan speed controller controls single-phase motors. The controller can work in 3 modes:
- Manual mode – The setting of minimum, and maximum speed is adjusted by trimmers, the current value of speed is adjusted by potentiometers on the front panel, Switched ON Kick Start with a duration of 8 sec. ;
- Pseudo-manual mode – The setting of minimum, and maximum speed is adjusted by trimmers, and the current value of speed is adjusted by potentiometers on the front panel, adding the possibility for ON / OFF of Kick Start and programming its duration from 1 to 20 sec. via MODBUS;
- MODBUS mode – Setting the minimum, maximum speed, current speed value, ON / OFF option of Kick Start and programming its duration from 1 to 20 sec. is performed through MODBUS;
In all modes, the controller can be stopped or started via MODBUS.
In MODBUS mode, the controller is suitable for connection to SCADA automation systems
Electrical parameters:
- Power supply range: 230 VAC / 50 Hz; +/- 10%;
- Maximum output current:3A/ 6A;
- Adjustable output voltage via potentiometer on the front panel or MODBUS;
- Adjustable value of minimum and maximum speed via trimmers on the front panel (inner side) or MODBUS;
- Overheat controller protection with two functions;
- 230 VAC fuse protected unregulated output;
- Fuse protected output;
- Switch ON/OFF with light
- Datasheet: DS-TSC-CM-x.pdf (Contact us).
- User guide: TSC-CM-user-guide.pdf (Contact us).
- Ordering info:
- TSC-CM-3 – wall mounting, for maximum current 3A;
- TSC-CM-6 – wall mounting, for maximum current 6A;
TSC-AB-3 / TSC-AB-6
TSC-CB-3 / TSC-CB-6
Triac controller with BLUETOOTH control
This electronic fan Bluetooth speed controller controls single-phase motors with/without thermal contacts The maximum motor current is 3/6 A. The fan speed can be set by the Android application via Bluetooth communication. The supply voltage is 230 VAC / 50 Hz; +/- 10%. The minimum, maximum speeds and the initial start are regulated by the application. An illuminated ON-OFF switch is located on the side of the housing. The unregulated output is active when the motor is activated. The CA monitoring function deactivates the engine in case of overheating. The alarm output is activated in case of motor problems.
Electrical parameters:
- Power supply range: 230 VAC / 50 Hz; +/- 10%;
- Maximum output current:3A/ 6A;
- The fan speed can be set by the Android application via Bluetooth communication.
- 230 VAC fuse protected unregulated output;
- Fuse protected output;
- Switch ON/OFF with light
- Datasheet: DS-TSC-CB-x.pdf (Contact us).
- User guide: TSC-B-user-guide.pdf (Contact us).
- User manual: User_Manual_TSC-xB.pdf (Contact us).
- Ordering info:
- TSC-AB-3 – panel mounting, for maximum current 3A;
- TSC-AB-6 – panel mounting, for maximum current 6A;
- TSC-CB-3 – wall mounting, for maximum current 3A;
- TSC-CB-6 – wall mounting, for maximum current 6A;
TSC-A-3 / TSC-A-6
TSC-C-3 / TSC-C-6
Triac controller with MANUAL control
This electronic fan speed controller controls single-phase motors with TK or thermal contacts. The fan speed can be set via the potentiometer on the front panel. The supply voltage is 230 VAC / 50 Hz – +/- 10%. The minimum and maximum speed is adjustable via trimmers on the front panel. An illuminated ON-OFF switch is located on the front panel. The unregulated output is active when the motor is enabled. The TK monitoring function deactivates the motor in case of overheating. The alarm output is activated in case of motor or controller problems.
Electrical parameters:
- Power supply range: 230 VAC / 50 Hz ; +/- 10%;
- Maximum output current: 6A / 10A;
- 230 VAC fuse protected unregulated output;
- Adjustable output voltage via potentiometer on front panel;
- Adjustable value of minimum and maximum speed via trimmers on front panel;
- 230 VAC alarm output, protected by fuse *;
- TK monitoring for thermal motor protection or temperature conctacts *;
- The Kick-start is 8s with adjusted via trimmer maximum speed;
- Overheat controller protection with two functions;
- Fuse protected output;
- Switch ON/OFF with light.
* – only TSC-C-3 / TSC-C-6 version .
- Datasheet: DS-TSC-C-x.pdf (Contact us).
- Ordering info:
- TSC-A-3 – panel mounting, for maximum current 3A;
- TSC-A1-3* – panel mounting, for maximum current 3A without TK protection and unregulated 230VAC alarm output;
- TSC-A-6 – panel mounting, for maximum current 6A;
- TSC-A1-6* – panel mounting, for maximum current 6A without TK protection and unregulated230VAC alarm output;
- TSC-C-3 – wall mounting, for maximum current 3A;
- TSC-C1-3* – wall mounting, for maximum current 3A without TK protection and unregulated 230VAC alarm output;
- TSC-C-6 – wall mounting, for maximum current 6A;
- TSC-C1-6* – wall mounting, for maximum current 6A without TK protection and unregulated230VAC alarm output;
TSC-B-3 / TSC-B-6
TSC-D-3 / TSC-D-6
Triac controller with ANALOG control
TSC-B/D-x is a motor speed controller. It has been designed for use with machining equipment and can be mounted on the wall or of the electrical control system. These electronic speed controllers automatically control the speed of single-phase voltage-controllable electric motors with TK or thermal contacts. The controller has a control input that permits to control of the motor using an external voltage 0-10VDC or 0-20mA. The maximum motor current is 10 A. The supply voltage is 230 VAC / 50 Hz; +/- 10%. The minimum, maximum speed, OFF level, type of analog input or kick-start is adjustable via buttons on the front panel.
There are LEDs on the front panel to indicate the current speed or values of different adjustments. An illuminated ON-OFF switch is located on the front of the enclosure. The unregulated output is active when the motor is enabled. The TK monitoring function deactivates the motor in case of overheating. The alarm output is activated in case of motor problems.
Electrical parameters:
- Power supply range: 230 VAC / 50 Hz; +/- 10%;
- Fuse-protected regulated output with maximum output current: up to 10A;
- Unregulated fuse protected output (230 VAC / max. 2 A) for 3-wire motor connection or voltage supply;
- Relay output: 2А / 230VAC;
- Analog input signal: 0—10VDC / 0-20mA
- TK monitoring for thermal motor protection or temperature contacts ;
- Adjustable via buttons on the front panel:
- Minimum, maximum speed;
- OFF level: 0-4VDC/ 0-8 mA;
- Type of analog input: current / voltage;
- Kick start: 0-20 seconds;
- Overheat controller protection;
- Switch ON/OFF with light;
- Operating and fault detection LEDs indications;
- Datasheet: DS-TSC-B/D-x.pdf (Contact us).
- User guide: TSC-B-user-guide-EN.pdf (Contact us).
- Ordering info:
- TSC-B-3 – panel mounting, for maximum current 3A;
- TSC-B-6 – panel mounting, for maximum current 6A;
- TSC-D-3 – wall mounting, for maximum current 3A;
- TSC-D-6 – wall mounting, for maximum current 6A;